Sailboat Listings sailboats for sale.Anote.Anytime.Internet, due to the geographic reach.Cetol Software Cost' title='Cetol Software Cost' />Aspire is built on the same platform as Vectrics VCarve Pro software, sharing the intuitive interface and ease of use for production design and routing.Agenda The program is daily updated, so please keep an eye on the agenda and visit the conference website for any further news.It.Nigeria scam. Requests.Please.Be especially careful of any transactions from overseas.Never give your password to anyone.Sailboat.Listings.Any such request is an attempt at phishing.Be.Contact. the buyer or seller by non cell phone as well as online.If a boat is not where it says it is, this is a strong indication of fraud.After discussing the details, have the boat surveyed and arrange to see the boat before any money changes hands.Adirondack Chair 1.Steps with PicturesIntroduction Adirondack Chair.Popular.Mechanics.For more on Adirondack Chairs, see our original story.Our version of the Adirondack chair has come a long way from the early types that had flat backs and seats and, weve added a matching table.Dont be intimidated by the curved slats and number of pieces in this project.Although there are a few angles and curves to cut, theres actually no fancy joinery everythings held together with deck screws.We used cedar for these pieces because it stands up well to the elements, and its available in the required 34 and 1 in.You could substitute pine if you plan to keep the chairs out of the weather.Step 1 Plans and Materials QTY.SIZE DESCRIPTION.A.B. 1 1 x 4 14 x 2.C.D. 9 34 x 2 14 x 2.E.F. 2 1 x 4 14 x 2.G.H. 2 1 x 2 34 x 6 12 cedar arm bracket.I. Install Ruby On Rails With Postgresql String . J. 2 1 x 5 14 x 1.K.L. 2 1 x 5 x 1.M.N. 5 1 x 3 34 x 2.O.No.P. as required 2 No.Step 2 Making the Seat.Lay out the side rail shape on your stock, cut to the lines with a jigsaw and sand the edges smooth.Then, cut the back rails to size, and saw the curves that give the chair back its concave shape.Note that the cut on the top rail is square, while the bottom rail has a 7 degree bevel.Cut the seat slats to size and round the upper edges of each with a 14 in.Then, round the exposed edges those that wont abut other parts of the side and back rails.Keep the router table set up for this job so you can round the edges of the other parts as theyre made.Because of the shape of the seat, most of the slats require bevels on one or both edges.Use a table saw or hand plane to cut the bevels.Step 3 Assemble the Seat.Start seat assembly by screwing the lower back rail to the seat sides with one screw at each end of the rail.Then, add slat No.Measure opposite diagonals of the subassembly and adjust it until its square.When youre satisfied, add a second screw to each end of the two slats to lock the pieces in position.Step 4 Arrange Slats.Use a 1 in.Then install the remaining slats.Because the seat is curved and many of the slat edges are angled, dont try to measure these spaces.Instead, simply arrange the slats by eye so that they appear uniform.Step 5 Attach Legs.Cut the front legs to size and round the long edges on the router table.Mark a line on the inside face of each leg that indicates the bottom edge of the side rail.Then, attach the legs to the seat assembly with screws driven from the inside of the side rails.Step 6 Add the Back.The back slats are tapered to create a fan shape when installed.Cut each 3.We did this on a band saw, but a jigsaw will work, too.Smooth the sawn surfaces, cut the curved top ends and round the edges.Cut the rear legs to size, angling the top ends at 6.Clamp each rear leg to a side rail, bore and countersink screw pilot holes, and secure the legs with screws.Step 7 Attach Back Rail.Screw the top back rail to the top ends of the back legs, and lay the chair on its back to install the back slats.Step 8 Align Slats.Place a 4 in.Mark the centers of the top and bottom back rails, align the center back slat with these marks and screw it in place.Note no laser beams were used in this assembly the original picture is damaged.Step 9 Secure Slats.Install the outer two slats.Secure the remaining slats so the top curved ends are aligned and the spaces are uniform.Since the back slats are the focal point of the chair, any gap too large or too small, will immediately draw your eye, so uniformity here is very important.Step 1.Install the Arms.Cut out the arms and arm supports, and round the edges.Temporarily clamp the supports in place and secure them with screws.Step 1.Attach Arms.Attach the arms to the front and rear legs with screws.Step 1.Make the Table.The table is built the same way as the chair all exposed edges are rounded on the router table and the parts are simply screwed together.Lay out the feet on 1 in.Attach each foot with three screws.Step 1.Attach Stretchers.Bore pilot holes and screw the two stretchers to the legs.Step 1.Space Slats.To assemble the top, its easiest to first clamp the pieces together with 38 in.Then, attach the cleats use the base sub assembly to make sure theyre spaced properly.Step 1.Attach Cleats to Base, Finish.Finally, screw the base to the top cleats.Lightly sand the chair and table with 1.Keep in mind, though, that cedar is a soft, oily wood that doesnt sand as well as pine or hardwood.You wont achieve the silky smooth surface that youd expect on indoor furniture.We finished our pieces with Sikkens Cetol 1, 0.Cedar.First, wipe all the sanding dust from the wood, then apply a coat of finish with a natural bristle brush.Allow each coat to dry for 2.Three coats should provide adequate protection from the elements.Ccie 100 Success Secrets Download Itunes .
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |